CHAPTER 1 Properties of gases.1
1.1 Gas equations 1
1.1.1 Ideal gas equations.. 2
1.1.2 Gas index equation.. 3
1.1.3 Actual gas equation. 5
1.1.4 Degree of gas molecular freedom .. 5
1.1.5 Specific heat capacity 7
1.2 Viscosity ..7
1.3 Property of wet gas .11
1.3.1 Pressure .. 12
1.3.2 Humidity. 13
1.3.3 Dew point temperature 14
References 14
CHAPTER 2 Gas lubrication equations. 15
2.1 Reynolds equation 15
2.1.1 Derivation of Reynolds equation.. 16
2.1.2 Reynolds equation in the polar coordinate system . 19
2.1.3 Reynolds equation in the cylindrical coordinate system.. 19
2.1.4 Lubrication parameters .. 20
2.2 Energy equation.22
2.2.1 Chang of gas inner energy 23
2.2.2 External work on gas and energy loss 24
2.3 Solid heat conduction equation and the interface equation ..26
2.4 Numerical analysis method.27
2.4.1 Finite difference method 27
2.4.2 Flow conservation. 28
2.4.3 Friction force balance . 34
References 35
CHAPTER 3 Isothermal gas lubrication .. 37
3.1 Sliders .37
3.1.1 Lubrication equation 38
3.1.2 Pressure boundary condition 40
3.1.3 Lubrication performance parameters.. 40
VI Contents
3.2
3.3
CHAPTER 4
4.1
4.2
4.3
4.4
3.1.4 Hydrodynamic lubrication characteristics of sliders.. 41
3.1.5 Hydrodynamic lubrication characteristics of divergent sliders .. 43
3.1.6 Lubrication characteristics of the magnetic head slider . 45 Journal bearing and radial seal .51
3.2.1 Lubrication equations.. 52
3.2.2 Boundary conditions 52
3.2.3 Lubrication parameters .. 53
3.2.4 Lubrication characteristics 55
Spiral groove thrust bearing56
3.3.1 Gas lubrication equations.. 59
3.3.2 Pressure boundary conditions . 60
3.3.3 Lubrication parameters .. 60
3.3.4 Lubrication characteristics 61
3.3.5 Spiral groove face seal 64
3.3.6 Lubrication equations.. 65
3.3.7 Pressure boundary conditions . 65
3.3.8 Seal performance parameters.. 66
3.3.9 Lubrication regularity . 66
References 71
Gas thermohydrodynamic lubrication of rigid surfaces.. 73 Sliders .73
4.1.1 Gas lubrication equations.. 73
4.1.2 Boundary conditions 75
4.1.3 Thermal lubrication characteristics . 75
Journal bearing and radial seal .79
4.2.1 Lubrication equations.. 79
4.2.2 Thermal boundary condition 80
4.2.3 Lubrication property 80
Spiral groove thrust bearing83
4.3.1 Lubrication equations.. 83
4.3.2 Boundary conditions 85
4.3.3 Lubrication property 86
Spiral groove face seal..86
4.4.1 Temperature characteristics of gas film 91
4.4.2 Lubrication property 94
References 99
Contents VII
CHAPTER 5 Gas thermoelastohydrodynamic lubrication of face seals . 101
5.1 Fundamental equations101
5.1.1 Lubrication equations 101
5.1.2 Boundary conditions . 104
5.2 Choked fluid effect107
5.2.1 Model validation . 107
5.2.2 Pressure distribution characteristics . 109
5.3 Characteristics of thermoelastic distortions of seal faces..109
5.4 Characteristics of gas thermoelastohydrodynamic lubrication..111
5.4.1 Mechanical distortions . 111
5.4.2 Thermal distortions 115
5.4.3 Thermoelastic distortions 117
References. 120
CHAPTER 6 Transient thermoelastohydrodynamic gas lubrication of face seals 121
6.1 Fundamental equations121
6.1.1 Dynamic equations. 122
6.1.2 Lubrication equations 122
6.1.3 Boundary conditions . 123
6.1.4 Dynamic characteristic parameter . 123
6.2 Dynamic characteristics of isothermal gas lubrication .124
6.2.1 Axial stiffness and damping . 124
6.2.2 Angular stiffness and damping 126
6.2.3 Amplitude-frequency characteristics of gas film .. 129
6.3 Dynamic characteristics of thermal gas lubrication of rigid surfaces 130
6.3.1 Axial stiffness and damping . 131
6.3.2 Angular stiffness and damping 134
6.3.3 Amplitude-frequency characteristics of gas film .. 137
6.4 Dynamic characteristics of gas thermoelastohydrodynamic lubrication..137
6.4.1 Axial stiffness and damping . 137
6.4.2 Angular stiffness and damping of gas film .. 139
6.4.3 Amplitude-frequency characteristics of gas film. 140 References. 141
VIII Contents
CHAPTER 7 Vapor-condensed gas lubrication of face seals .. 143
7.1 Fundamental equations143
7.1.1 Wet gas equations .. 143
7.1.2 Vapor-condensed parameter . 145
7.2 Characteristics of vapor condensation in gas lubrication film 145
7.3 Laws of vapor condensation in gas lubrication film..146
7.3.1 Humidity.. 146
7.3.2 Seal clearance 147
7.3.3 Seal pressure . 148
7.3.4 Rotational speed.. 148
7.4 Movement of liquid drops on gas lubrication surfaces.150
7.4.1 Surface wetting model . 150
7.4.2 Surface-texture geometry parameters and wettability 152
7.4.3 Droplet motion . 158
7.4.4 Drop adsorption on seal surface . 164
References. 164
CHAPTER 8 Cryogenic gas lubrication of face seals 167
8.1 Fundamental equations167
8.1.1 Lubrication equations 168
8.1.2 Boundary conditions . 171
8.2 Phase change in gas lubrication film..172
8.3 Characteristics of thermoelastic distortions of seal faces 173
8.4 Characteristics of cryogenic gas lubrication173
8.4.1 Ambient temperature 174
8.4.2 Rotation speed.. 174
References. 177
CHAPTER 9 Surface grooves of gas face seals and testing technology.. 179
9.1 Surface grooves of gas face seals .179
9.2 Testing technology of gas face seals ..185
9.2.1 Experimental setup. 185
9.2.2 Face groove machining 185
9.2.3 Face morphology test 187
9.3 Experimental characteristics of gas face seals ..188
9.3.1 Seal opening characteristic 188
9.3.2 Hydrodynamic characteristics.. 190
Contents IX
9.3.3 Surface wear.. 192
References. 195
CHAPTER 10 Design of gas face seals 197
10.1 Force analysis of gas seals197
10.1.1 Opening force. 198
10.1.2 Closing force.. 198
10.1.3 O-ring friction force 199
10.2 Geometric parameters of gas face seals 199
10.2.1 Seal clearance. 199
10.2.2 Seal face width.. 199
10.2.3 Balance diameter.. 200
10.2.4 Seal face and shaft (shaft sleeve) clearance.. 200
10.3 Performance parameters of gas face seals201
10.3.1 Leakage rate 201
10.3.2 Gas film stiffness . 201
10.4 Materials of the seal couple .202
10.5 Dimension design of seal rings..202
10.5.1 Design of rotor dimension .. 202
10.5.2 Design of stator dimension . 203
10.5.3 Design of the face groove 204
10.6 Design of the secondary seal ..205
10.7 Process of seal design and illustration205
10.7.1 Process of seal design 205
10.7.2 Design conditions. 206
10.7.3 Design steps 206
References. 218
Index .219
內容試閱：
Gas lubrication is a form of fluid lubrication， which uses air or working medium gas as a lubricant to separate two friction pairs moving in relation to each other. It has the advantages of low friction resistance， high working accuracy， and a wide range of applicable temperatures， and is widely used in the design of gas-eous static pressure bearings， high-speed thrust bearings， foil bearings， mechanical seals， and other mechanical parts and equipment under extreme conditions such as extremely high or low temperatures， ultra-high or -low speeds， and ultra-precision.
In 1854， Hirm came up with the idea of using gas as a lubricant. In 1886， Reynolds deduced the Reynold’s equation describing the pressure distribution of fluid lubrication film， which raised people’s understanding of the principle of fluid lubrication to a theoretical height. In the 1950s， research on gas lubrication theory based on bearing design requirements developed rapidly. In 1959， Elrod and Burgdorfer theoretically explained that the temperature rise effect inside the lubrication gas film could be ignored under general working conditions， and the isothermal hypothesis was generally accepted in gas lubrication analysis. After the 1980s， the development of magnetic storage technology pushed the film thick-ness of gas bearings from microns to nanometers， and microscopic effects such as the gas thinning effect and surface roughness were widely studied， which pro-moted the development of gas thin film lubrication theory.
With an increase of rotation speed in mechanical equipment and the appear-ance of new bearing structures， the problem of gas thermodynamic lubrication became increasingly prominent. For example， in a gas hydrostatic bearing under the conditions of a film thickness of 20 μm， pressure of 0.7 MPa， and rotation speed of 20，000 rpm， shear heat can cause the gas film lubrication temperature to rise above 30°C. The increase of rotor temperature rise and gas viscosity can improve the stiffness and damping coefficient of the bearing， but in the absence of sufficient cooling， the bearing is prone to thermal instability， which is particu-larly prominent in a high-speed bearing design.
Compared with bearing gas lubrication dominated by shear flow， there is also pressure flow caused by seal pressure in the gas seal lubrication area. In the pro-cess of gas leakage flow from the high-pressure side to the low-pressure side， gas film temperature decreases because of rapid volume expansion， resulting in ther-mal distortion and other gas thermohydrodynamic lubrication problems.
In 1968， the John Crane Company first developed the circular arc surface spiral groove gas-lubricated seal and introduced plane spiral groove gas-lubricated seal products. With the development of gas sealing technology to high-temperature， high-pressure， high-speed， and other high parameters; the diversification of sealing media; and the continuous expansion of application fields， the surface thermal dis-tortion， supersonic flow， media phase change， and other gas thermohydrodynamic lubrication problems are increasing.
Preface
Based on the research methods and results of elastohydrodynamic lubrication theory of Prof. Wen Shizhu， this book summarizes the research results of the authors in recent years. Grounded in the application background of lubrication design of high-speed gas bearings and high-pressure gas seals， theory and analysis methods of gas thermohydrodynamic lubrication are systematically expounded. In this book， theoretical model and lubrication characteristics of gas lubrication are discussed for typical bearings and seals.
The book is divided into 10 chapters.
In Chapter 1， Properties of gases， properties of gases are introduced. Based on the principle of energy equipartition， the ideal gas state equation is decomposed into two independent gas equations.
In Chapter 2， Gas lubrication equations， the derivation of the Reynolds equa-tion， energy equation， heat conduction equation， interface equation， and other basic lubrication equations are explained. The lubrication analysis of force bal-ance and flow conservation problems are also discussed.
In Chapter 3， Isothermal gas lubrication， we introduce the modeling method and basic lubrication characteristics of isothermal gas lubrication of typical struc-tures such as the slider bearing， radial bearing， thrust bearing， and face seal.
In Chapter 4， Gas thermohydrodynamic lubrication of rigid surfaces， the gas thermodynamic lubrication law of gas-lubricated bearings and low-pressure gas seals under high-speed working conditions are analyzed without consideration of surface distortions.
Chapter 5， Gas thermoelastichydrodynamic lubrication of face seals， discusses the high-pressure gas face seal， the modeling method of TEHL， and fundamental characteristics of choked flow effect， thermoelastic distortion of seal faces， and the temperature distribution of gas film.
In Chapter 6， Transient thermoelastichydrodynamic gas lubrication of face seals， targets the gas face seal， dynamic load characteristics of the seal gas film under the conditions of isothermal lubrication， rigid surface thermal lubrication， and TEHL， exploring these in detail.
Chapter 7， Vapor-condensed gas lubrication of face seals， explores the face seal of high-pressure gas， the law of condensation and precipitation of water vapor in the seal gas film， and the movement of liquid drops in the seal gap under TEHL conditions.
Chapter 8， Cryogenic gas lubrication of face seals， uses the inclined ellipse dimpled gas face seal as an example and natural gas as the sealing medium to introduce the modeling method of cryogenic gas lubrication and the fundamental characteristics of phase change in seal film and thermoelastic distortion of seal faces.
In Chapter 9， Surface grooves of gas face seals and testing technology， typical seal grooves and their laser processing methods and experimental measurement methods are presented. Opening characteristics， hydrodynamic characteristics， and friction characteristics of gas face seals are discussed by taking the micro-dimpled face seal as an example.
Preface III
In Chapter 10， Design of gas face seals， an internal flow single-face spiral groove gas seal is used as an example to introduce the basic method and design process of gas face seals.
In the process of compiling this book， Prof. Huang Ping has given great sup-port and help. Here I would like to express my sincere gratitude. At the same time， I would like to express my heartfelt thanks to my colleagues and graduate students who have given me warm support and help in the preparation of this book.
Bai Shaoxian
Hangzhou
購物車/收銀台(
0
) | 在線留言板
| 付款方式
| 運費計算
| 聯絡我們
| 幫助中心 |
加入書簽
HOME
新書上架
